联系人:魏经理
电话:15165311861
手机:15165311861 15853170198
地址:济南市标山南路绿地东门
当前位置:首页-最新公告最新公告
玻璃门扇的安装,你了解吗?
作者:admin 来源:本站 发布时间:2018-09-07 14:46:40 浏览次数:97
玻璃门扇的启闭由地弹簧实现,地弹簧与门扇的上下金属横档进行铰接,下面为大家介绍一下玻璃门扇的安装说明。
The opening and closing of glass door is realized by ground spring. The ground spring is articulated with the upper and lower metal crossbar of the door. The following is an introduction to the installation of glass door.
1、划线:
1, marking:
在玻璃门扇的上下金属横档内划线,按线固定转动销的销孔板和地弹簧的转动轴连接板。具体操作可参照地弹簧产品安装说明。
Line the upper and lower metal crossbar of the glass door fan and fix the pin-hole plate of the rotating pin and the rotating shaft connecting plate of the ground spring according to the line. The specific operation can be referenced to the installation instructions of the spring products.
2、确定门扇高度:
2. Determine the height of door leaf.

玻璃门扇的高度尺寸,在裁割玻璃板时应注意包括插入上下横档的安装部分。一般情况下,玻璃高度尺寸应小于测量尺寸5mm 加左右,以便于安装时进行定位调节。把上、下横档(多采用不锈钢成型材料)分别装在厚玻璃门扇上下两端,并进行门扇高度的测量。如果门扇高度不足,即其上下边距门横框及地面的缝隙超过规 定值,可在上下横档内加垫胶合板条进行调节。

济南玻璃隔断

The height dimension of the glass door should include the mounting part inserted into the upper and lower crossbar when cutting the glass plate. In general, the glass height size should be less than 5 mm plus or so, so as to facilitate the installation of positioning adjustment. The upper and lower transverse gears (mostly made of stainless steel) are installed at the upper and lower ends of the thick glass door, and the height of the door is measured. If the height of the door fan is insufficient, that is, the gap between the upper and lower edges of the door frame and the ground exceeds the prescribed value, plywood strips can be padded in the upper and lower crosspieces for adjustment.
3、固定上下横档:
3, fixed upper and lower runway:
门扇高度确定后,即可固定上下横档,在玻璃板与金属横档内的两侧空隙处,由两边同时插入小木条,轻敲稳实,然后在小木条、门扇玻璃及横档之间形成的缝隙中注入玻璃胶。
When the height of the door is fixed, the upper and lower transverse gears can be fixed. In the space between the glass plate and the metal transverse gears, small wooden bars are inserted at the same time on both sides, and a firm tap is made. Then glass glue is injected into the gap formed between the small wooden bars, the glass of the door fan and the transverse gears.
4、门扇固定:
4, door leaf fixed:
进行门扇定位安装。先将门框横梁上的定位销本身的调节螺钉调出横梁平面1~2mm,再将玻璃门扇竖起来,把门扇下横档内的转动销连接件的孔位对准地弹簧的转动销轴,并转动门扇将孔位套人销轴上。然后把门扇转动90°使之与门框横梁成直角,把门扇上横档中的转动连接件的孔对准门框横梁上的定位销,将定位销插入孔内15mm 左右(调动定位销上的调节螺钉)。
Positioning and installation of door leaf. Firstly, the adjusting screw of the positioning pin itself on the door frame cross beam is adjusted out of the cross beam plane by 1-2 mm, and then the glass door fan is erected. The hole position of the rotating pin connector in the lower crossbar of the door fan is aligned with the rotating pin shaft of the ground spring, and the door fan is rotated to cover the hole position on the pin shaft. Then turn the door fan 90 degrees to make it right angle with the door frame crossbeam, align the hole of the rotating connector in the upper crossbar of the door fan with the positioning pin on the door frame crossbeam, and insert the positioning pin into the hole about 15mm (adjusting screw on the positioning pin).
5、安装拉手:
5. Installation handle:
全玻璃门扇上的拉手孔洞,一般是事先订购时就加工好的,拉手连接部分插入孔洞时不能很紧,应有松动。安装前在拉手插入玻璃的部分涂少许玻璃胶;如若插入过松,可在插入部分裹上软质胶带。拉手安装时,其根部与玻璃贴紧后再拧紧固定螺钉。
Holes in the handle of all glass doors are usually processed before ordering. The connecting part of the handle can not be very tight when inserting holes. It should be loose. Before installation, a little glass glue is applied to the part where the glass is inserted by the handle; if the glass is inserted loosely, a soft adhesive tape can be wrapped on the part where the glass is inserted. When the handle is installed, the roots are tightly attached to the glass and then tighten the fixing screws.