联系人:魏经理
电话:15165311861
手机:15165311861 15853170198
地址:济南市标山南路绿地东门
当前位置:首页-新闻中心新闻中心
无框玻璃门的施工工艺
作者:山东玻璃门 来源:http://www.dljianlei.com/ 发布时间:2017-11-03 15:49:09 浏览次数:1614
无框玻璃门,就是门扇玻璃周边没有固结的边框。无框玻璃门一般都是用8~12mm的钢化玻璃做门扇的。无框玻璃门的安装方法与一般的玻璃门安装方法差不多,可是也有一些区别,柏尔斯现在就来给你介绍一下无框玻璃门的安装要点及安装方法。
Frameless glass door, glass door frame is not around the consolidation. Frameless glass doors are generally used 8~12mm glass door. The installation method of frameless glass door and the glass door installation method, but there are some differences, boersi now introduce to you without installation of frameless glass door and installation method.
01
01
无框玻璃门的安装要点:
Installation points of frameless glass door:
1、在所有的安装步骤开始之前,必须要确保在室内装修装饰的其他工序都施工基本结束后才能进行,而且在放线定位时要严格按照设计图纸要求进行。
1, before all the installation steps to start, must ensure that the interior decoration and decoration of other processes are basically completed after construction, and in line positioning should be strictly in accordance with the requirements of the design drawings.
2、在外包金属装饰面时,要把饰面对头接缝放置在安装玻璃的两侧中间位置。接缝位置必须准确并保证垂直。
In 2, outsourcing metal decorative surface, to finish butt joint is placed in the middle position installed on both sides of the glass. The seam position must be accurate and vertical.
3、无框玻璃门门框顶部限位槽的宽度应大于玻璃厚度2~4mm,槽深在20~30mm之间,以便注胶。
3. The width of the limiting slot on the top of the frameless glass door frame should be greater than the glass thickness of 2 ~ 4mm, and the groove depth is between 20 and 30mm, so as to glue injection.
4、在安装无框玻璃门的玻璃门扇时的就位方法是:应把玻璃上部插入门框顶部的限位槽内
4, in the installation of frameless glass door glass door location method is: the glass should be inserted into the upper limit of the door frame
然后把玻璃的下部放到底托上对正中心线,并对好两侧门框的安装位置,使厚玻璃的两侧边部正好封住门框的金属饰面对缝口,要求做到内外都看不见饰面接缝口。
Then put the glass on the lower part of the bottom bracket on the center line, and the installation position of the door on both sides of the good, the metal finishes on the thick glass edge on both sides of the door just seal the mouth, requires both inside and outside the invisible facing joint.
无框玻璃门的安装要点及安装方法
Installation of frameless glass doors and installation method
5、在进行无框玻璃门的玻璃之间对接过程中,对接缝的玻璃切口必须倒用,并且在玻璃固定后,要用玻璃胶入缝隙中,注满后同样要用塑料片把胶刮平,使缝隙形成一条洁净的均匀直线,玻璃面上要用干净布擦净胶迹。
5, in between the frameless glass door glass in the process of docking, the joint glass incision must be inverted, and the glass is fixed, to use glass glue is filled into the gap, to use the same piece of plastic glue scraping, the gap formed a clean glass surface to uniform linear. With a clean cloth wipe glue.
6、在注玻璃胶封口时,注入顺序应从某一条缝隙的端头开始到末端终止,中途不得停顿。

6, in the injection glass sealing, the injection sequence should start from the end of a gap to the end of the end, no pause in the middle.

山东玻璃门

02
02
无框玻璃门的安装方法:
Installation method of frameless glass door:
1、放线定位:无框玻璃门在安装之初,就必须对固定玻璃隔断及活动玻璃门扇统一放线定位,待确定门框位置,准确地测量地面标高及门框顶部标高。
1, positioning: frameless glass door in the beginning of the installation, must be fixed glass partition and moving glass door leaf unified positioning, to determine the position of the door frame, accurate measurement of the ground elevation and the top of the doorframe.
2、安装无框玻璃门门框顶部限位槽:由所弹中心线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。
2. Install the limit slot of frameless glass door frame top: draw two metal decorative board sideline from the center line of the projectile, and then install the limit slot on the top of the doorframe according to the side line.
3、安装无框玻璃门金属饰面的木底托:在原预埋木砖上钉方木,或通过膨胀螺栓钉方木,把方木固定在地面上,然后再用万能胶将金属饰面板粘在木方上。
3, the installation of frameless glass doors of metal decorative wood base: in the original embedded block nail in wood, or through the expansion bolt nail in wood, the wood is fixed on the ground, then the adhesive to metal decorative panel glued on wood.
4、安装坚向门框:按所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形尺寸和位置的固定,当固定好以后,再外包金属装饰面。
4, the installation of vertical frames: according to the elastic line nail vertical door frame timbers, and then determine the plywood shape size and position of the door frame is fixed, when fixed, then outsourcing metal decorative surface.
无框玻璃门的安装要点及安装方法
Installation of frameless glass doors and installation method
5、无框玻璃门的玻璃门扇安装:用玻璃吸盘器(或玻璃吸盘机)把厚玻璃吸紧吸住,然后手握吸盘把通过2~3人把厚玻璃板抬起并竖立起来移至安装地点准备就位。
5, frameless glass door glass door with glass sucker (or glass sucker machine) thick glass ceiling tight grip, and then holding the chuck by 2 ~ 3 thick glass plate is raised and erected to installation site preparation in place.
6、玻璃固定:在底托木上的内外钉两根扁方木条把厚玻璃夹在中间,但距厚玻璃板需留出4mm左右的空隙,然后在扁方木条上涂刷万能胶将饰面金属板粘卡在方木和两根扁方木条上。
6, glass fixed: inside and outside at the bottom of the nails used two flat square batten thick glass in the middle, but from the thick glass to void leaving about 4mm, and then painted on the flat side of wood adhesive to decorative metal plate sticking on square and two flat square timber.
7、注玻璃胶封口:在顶部根位槽两侧空隙内和底托玻璃槽口的两侧以及厚玻璃与门框柱的对缝处注入玻璃胶。
7, note: sealing glass glue on both sides of the supporting glass notch and thick glass and frame column on the injected plastic glass at the top of the root slot and the bottom gap on both sides.
8、无框玻璃门的玻璃之间对接:固定部分的厚玻璃板,由于宽度尺寸过大,必须用两块或两块以上进行拼装而成,两块对齐拼接必然形成接缝,对接缝应留2~3mm的距离。

The docking between 8 and frameless glass door glass: thick glass plate of the fixed part, the width is too large, must use 2 or more blocks are assembled, a mosaic alignment must form the joint should be 2 ~ 3mm distance to seam.

以上文章来源于山东玻璃门厂家http://www.dljianlei.com/